SA2400A中文資料Single chip transceiver for 2.45 GHz ISM band數(shù)據(jù)手冊(cè)恩XP規(guī)格書

描述 Description

DESCRIPTION
The SA2400A is a fully integrated single IC RF transceiver designed for 2.45 GHz wireless LAN (WLAN) applications. It is a direct conversion radio architecture that is fabricated on an advanced
30 GHz fTBiCMOS process. The SA2400A combines a receiver, transmitter, and LO generation into a single IC.FUNCTIONAL BLOCKS AND FEATURES
The block diagram of the SA2400A Direct Conversion transceiver is given in Figure 1. It consists of the following functional blocks:
?A 79 dB adjustable gain range direct conversion zero IF receiver with 3 μs (typical) Tx to Rx switching time, and comprising the following:
– Front-end LNA with two internal gain states
– A fast on-chip closed loop composite RF and IF AGC with zoomed analog RSSI output and 8 μs settling time
– Quadrature downconverters from 2.45 GHz RF directly to zero IF
– On-chip fast baseband DC cancellation with automatically stepped bandwidths of 10 MHz, 1 MHz, 100 kHz, and 10 kHz, settling within 8–13 μs for a DC error of 10% that decays to 1%.
– Fully integrated channel filters, appropriate for 11 Msymbols/s QPSK modulation RF bandwidth.
?An I/Q upconverter from baseband directly to 2.45 GHz, with +8 dBm output power, –40 dBc typical carrier leakage (calibrated) and 3 μs (typical) Rx to Tx switching time, and comprising the following:
– Wide band IQ modulator producing better than 14% EVM for 11 Msymbols/s QPSK modulation
– Integrated reconstruction and spectral shaping filters at I and Q modulation input that is driven by an external D/A. High common mode rejection to input ground bounce.
– FIR-DACs for digital I/Q input feeding the analog signal path and including additional filtering for spectral shaping.
– 2.45 GHz power amplifier driver with +8 dBm maximum output, 15 dB adjustable gain in 1 dB steps and a second switched output at –1.5 dBm power level with similar gain adjustments that are set by a separate register.
– Completely on-chip calibration for Carrier Leakage compensation.
– Internal power ramping with 2 μs delay and 0.5 μs ramp-up time.
?A fractional-N frequency synthesizer with on-chip VCO and XO
?A 3-wire bus for control of most blocks
?An additional high speed 3-wire bus for full control of Rx-Gain and DC-offset compensation parameters with 44Mbits/s.
?Fast Tx-Rx switching based on a single digital input pin.
?Reference currents and voltage for supply of Baseband Processor and PA-chip.APPLICATIONS
?IEEE 802.11 and 802.11b radios
? – Supports DSSS and CCK modulation
? – Supports data rates: 1, 2, 5.5, and 11 Mbps
?2.45 GHz ISM band wireless communication devices

特性 Features

The block diagram of the SA2400A Direct Conversion transceiver is given in Figure 1. It consists of the following functional blocks:
?A 79 dB adjustable gain range direct conversion zero IF receiver with 3 μs (typical) Tx to Rx switching time, and comprising the following:
– Front-end LNA with two internal gain states
– A fast on-chip closed loop composite RF and IF AGC with zoomed analog RSSI output and 8 μs settling time
– Quadrature downconverters from 2.45 GHz RF directly to zero IF
– On-chip fast baseband DC cancellation with automatically stepped bandwidths of 10 MHz, 1 MHz, 100 kHz, and 10 kHz, settling within 8–13 μs for a DC error of 10% that decays to 1%.
– Fully integrated channel filters, appropriate for 11 Msymbols/s QPSK modulation RF bandwidth.
?An I/Q upconverter from baseband directly to 2.45 GHz, with +8 dBm output power, –40 dBc typical carrier leakage (calibrated) and 3 μs (typical) Rx to Tx switching time, and comprising the following:
– Wide band IQ modulator producing better than 14% EVM for 11 Msymbols/s QPSK modulation
– Integrated reconstruction and spectral shaping filters at I and Q modulation input that is driven by an external D/A. High common mode rejection to input ground bounce.
– FIR-DACs for digital I/Q input feeding the analog signal path and including additional filtering for spectral shaping.
– 2.45 GHz power amplifier driver with +8 dBm maximum output, 15 dB adjustable gain in 1 dB steps and a second switched output at –1.5 dBm power level with similar gain adjustments that are set by a separate register.
– Completely on-chip calibration for Carrier Leakage compensation.
– Internal power ramping with 2 μs delay and 0.5 μs ramp-up time.
?A fractional-N frequency synthesizer with on-chip VCO and XO
?A 3-wire bus for control of most blocks
?An additional high speed 3-wire bus for full control of Rx-Gain and DC-offset compensation parameters with 44Mbits/s.
?Fast Tx-Rx switching based on a single digital input pin.
?Reference currents and voltage for supply of Baseband Processor and PA-chip.