Smart, simple solutions for the 12 most common design concerns

文件：727.81 Kbytes 頁數：8 Pages

恩XP

Fm I2C-bus advanced stepper motor controller

文件：1.35911 Mbytes 頁數：59 Pages

恩XP

Fm+ I2C-bus advanced stepper motor controller

The PCA9629A is an I2C-bus controlled low-power CMOS device that provides all thelogic and control required to drive a four phase stepper motor. PCA9629A is intended tobe used with external high current drivers to drive the motor coils. The PCA9629Asupports three stepper motor drive formats: one-pha ? Generate motor coil drive phase sequence signals with four outputs for use withexternal high current drivers to off-load CPU\n? Four balanced push-pull type outputs capable of sinking 25 mA or sourcing 25 mA forglueless connection to external high current drivers needed to drive unipolar steppermo;

恩XP

Fm+ I2C總線步進電機控制器

PCA9629是一款I(lǐng)2C總線控制的低功率CMOS器件，提供驅動一個四相位步進電機所需的所有邏輯和控制。PCA9629是為配合外部高電流驅動器使用以驅動電機線圈而設計。PCA9629支持三種步進電機驅動格式：?jiǎn)蜗啵ú?qū)動）、兩相和半步進此外，當用作輸入時，四個通用輸入/輸出(GPIO)允許感應來自光中斷器模塊的邏輯電平輸出并在PCA9629的INT引腳上生成低電平有效的中斷信號。在感應電機軸原始位置或步進參考脈沖時，此功能很有用。中斷時，可對PCA9629進行編程以自動停止電機或反轉電機的旋轉方向。\n使用控制寄存器可對輸出波列進行編程。通過 I2C總線可對控制寄存器進行編程。PCA9629的 使用四個輸出生成電機線圈驅動相位序列信號以使用外部高電流驅動器，使CPU沒有負載\n四個平衡的推挽式輸出能灌入25 mA或拉出25 mA，用于無縫連接驅動電機線圈所需的外部高電流驅動器具有100 ns上升和下降時間的最大1000 pF負載\n\n內置振蕩器無需外部組件\n步進電機驅動控制邏輯\n單相（波驅動）、兩相和半步驅動格式的邏輯電平輸出\n可編程步進速率：344.8 kpps至0.3 pps，±5 %的精度\n可編程緩升啟動和緩降停止\n可編程步進和旋轉控制\n通過傳感器啟用的驅動控制：與I/O引腳的中斷鏈接\n電機軸的方向控制\n電機軸的可選擇主動保持、電源關閉或釋放狀態\n四;

恩XP