36V, 3.8A Two H-Bridge for Dual Brushed or Single Stepper Motor Drive

General Description The MAX22211 is a dual 36V, 3.8AMAX H-bridge. It can be used to drive two brushed DC motors or a single stepper motor. The H-bridge FETs have very low impedance resulting in high driving efficiency and low heat generation. The typical total RON (high-side + low-side) is 0.

文件：548.57 Kbytes 頁數：24 Pages

AD

亞德諾

用于兩個有刷或單個步進電機驅動器的 36V、3.8A 雙 H 橋

MAX22211 是一款雙通道 36V、3.8A MAX H 橋。它可用于驅動兩個有刷直流電機或單個步進電機。H 橋 FET 具有非常低的阻抗，因此，驅動效率較高且散熱很少?？?RON（高側 + 低側）的典型值為 0.25Ω。每個 H 橋可使用三個邏輯輸入（DIN1、DIN2、EN）單獨進行脈寬調制 (PWM) 控制。\n\n MAX22211 具有精確的電流驅動調節 (CDR) 功能，可用于限制有刷直流電機的啟動電流或控制步進操作的相電流。電橋輸出電流由無損耗式集成電流檢測 (ICS) 套件進行檢測，然后與用戶可配置的閾值 (ITRIP) 進行比較。當電橋電流超過 ITRIP 閾值 ? 兩個 H 橋，最大工作電壓為 +36V\n? 每個 H 橋的電流額定值（TA = 25°C 時的典型值）\n?IRMS = 2ARMS（每個全橋推薦的最大 RMS 電流）\n? 集成電流驅動調節?ICS 無需使用體積較大的外部電阻，提高了效率\n? 電流驅動調節監控輸出引腳（CDRA、CDRB）\n?半滿量程 (HFS) 引腳可在低電流范圍內提高電流控制精度;

ADI

亞德諾

36V, 3.8A Two H-Bridge for Dual Brushed or Single Stepper Motor Drive

General Description The MAX22211 is a dual 36V, 3.8AMAX H-bridge. It can be used to drive two brushed DC motors or a single stepper motor. The H-bridge FETs have very low impedance resulting in high driving efficiency and low heat generation. The typical total RON (high-side + low-side) is 0.

文件：548.57 Kbytes 頁數：24 Pages

AD

亞德諾

36V, 3.8A Two H-Bridge for Dual Brushed or Single Stepper Motor Drive

General Description The MAX22211 is a dual 36V, 3.8AMAX H-bridge. It can be used to drive two brushed DC motors or a single stepper motor. The H-bridge FETs have very low impedance resulting in high driving efficiency and low heat generation. The typical total RON (high-side + low-side) is 0.

文件：548.57 Kbytes 頁數：24 Pages

AD

亞德諾