36V, 3.8A Stepper Motor Driver with Integrated Current Sense and 128 Microstep Indexer

General Description The MAX22210 is a 2-phase stepper motor driver. It integrates two 36V, 3.8AMAX H-bridges. The H-bridge FETs have very low impedance that result in high driving efficiency and minimal heat generated. The typical total RON (high side + low side) is 0.25Ω. The MAX22210 integ

文件：350.51 Kbytes 頁數：24 Pages

AD

亞德諾

集成電流檢測和128微步分度器的36V、3.8A步進電機驅動器

MAX22210是一款2相步進電機驅動器。它集成了兩個36V、3.8AMAX H橋。\n\n H橋FET的阻抗非常低，因此驅動效率較高且發熱很少?？俁ON（高側 + 低側）的典型值為0.25Ω。\n\n MAX22210集成了一個精密的電流驅動調節電路和一個由STEP/DIR接口控制的128微步內置分度器。高微步分辨率和先進的控制技術可確保工作時保持平穩和安靜。\n\n 流入兩個低側FET的電流由無損耗式集成電流檢測(ICS)器件進行檢測，然后會與所需的步進閾值電流進行比較。一旦電橋電流超過設定值(ITRIP)，器件就會強制衰減，并保持一段固定的關斷時間(TOFF ? 兩個H橋的額定值為36V\n? 總RDS(ON) (HS + LS)：TA = +25°C時為250mΩ（典型值）\n? 每個H橋的電流額定值（TA = +25°C，典型值）\n?IFS = 3AMAX（內部電流驅動調節的滿量程電流設置）\n? 集成電流控制\n? 可使用外部電阻配置滿量程電流\n? 通過一路邏輯輸入(HFS)提高低電流值的電流控制精度\n? 提供內部電流檢測(ICS)功能，無需使用體積較大外部電阻器，提高了效率;

ADI

亞德諾

36V, 3.8A Stepper Motor Driver with Integrated Current Sense and 128 Microstep Indexer

General Description The MAX22210 is a 2-phase stepper motor driver. It integrates two 36V, 3.8AMAX H-bridges. The H-bridge FETs have very low impedance that result in high driving efficiency and minimal heat generated. The typical total RON (high side + low side) is 0.25Ω. The MAX22210 integ

文件：350.51 Kbytes 頁數：24 Pages

AD

亞德諾

36V, 3.8A Stepper Motor Driver with Integrated Current Sense and 128 Microstep Indexer

General Description The MAX22210 is a 2-phase stepper motor driver. It integrates two 36V, 3.8AMAX H-bridges. The H-bridge FETs have very low impedance that result in high driving efficiency and minimal heat generated. The typical total RON (high side + low side) is 0.25Ω. The MAX22210 integ

文件：350.51 Kbytes 頁數：24 Pages

AD

亞德諾