Low-Cost Ringing SLIC

Introduction The Agere Systems Inc. L9214 is a subscriber line interface circuit that is optimized to provide a very low-cost solution for short- and medium-loop applications. This device provides the complete set of line interface functionality, including power ringing needed to interface to a s

文件：790.61 Kbytes 頁數：46 Pages

AGERE

Short-Loop Sine Wave Ringing SLIC

Introduction The Agere Systems Inc. L9215 is a subscriber line interface circuit that is optimized for short-loop, power-sensitive applications. This device provides the complete set of line interface functionality (including power ringing) needed to interface to a subscriber loop. This device ha

文件：1.11502 Mbytes 頁數：50 Pages

AGERE

Short-Loop Ringing SLIC with Ground Start

Introduction The Agere Systems Inc. L9216 is a subscriber line interface circuit (SLIC) that is optimized for shortloop, power-sensitive applications. This device provides the complete set of line interface functionality, including power ringing needed to interface to a subscriber loop. This devi

文件：1.06289 Mbytes 頁數：48 Pages

AGERE

Low-Cost Line Interface with Reverse Battery and PPM

Description This general-purpose electronic subscriber loop interface circuit (SLIC) is optimized for low cost, while still providing a satisfactory set of features. This part is a pin-for-pin replacement for the Agere L9218/ L9219 SLIC. Features ■ Basic forward/reverse battery SLIC functionali

文件：414.51 Kbytes 頁數：30 Pages

AGERE

Low-Cost Line Interface

Description This general-purpose electronic subscriber loop interface circuit (SLIC) is optimized for low cost, while still providing a satisfactory set of features. The L9218 is pin-for-pin compatible with the Agere L9219 and L9217 SLICs. The L9218 requires a 5 V power supply and single batter

文件：378.92 Kbytes 頁數：30 Pages

AGERE

Low-Cost Line Interface with Reverse Battery and Dual Current Limit

Description This general-purpose electronic subscriber loop interface circuit (SLIC) is optimized for low cost, while still providing a satisfactory set of features. This part is a pin-for-pin replacement for the Agere L9217 and L9218 SLICs. The L9219 requires a 5 V power supply and single batte

文件：397.12 Kbytes 頁數：30 Pages

AGERE

QUAD INVERTING TRANSISTOR SWITCH

DESCRIPTION The L9222 monolithic quad transistor switch is designed for high current, high voltage switching applications. Each of the four switches is controlled by a logic input and all four are controlled by a common enable input. All inputs are TTL-compatible for direct connection to logic c

文件：91.01 Kbytes 頁數：5 Pages

STMICROELECTRONICS

意法半導體

SPI CONTROLLED H-BRIDGE

DESCRIPTION The L9230 is an SPI controlled H-Bridge, designed for the control of DC and stepper motors in safety critical applications and under extreme environmental conditions. ■ OPERATING SUPPLY VOLTAGE 5V TO 28V ■ TYPICAL RDSon = 150 m? FOR EACH OUTPUT TRANSISTOR (AT 25°C) ■ CONTINOUS DC L

文件：218.23 Kbytes 頁數：25 Pages

STMICROELECTRONICS

意法半導體

SPI CONTROLLED H-BRIDGE

DESCRIPTION The L9230 is an SPI controlled H-Bridge, designed for the control of DC and stepper motors in safety critical applications and under extreme environmental conditions. ■ OPERATING SUPPLY VOLTAGE 5V TO 28V ■ TYPICAL RDSon = 150 m? FOR EACH OUTPUT TRANSISTOR (AT 25°C) ■ CONTINOUS DC L

文件：218.23 Kbytes 頁數：25 Pages

STMICROELECTRONICS

意法半導體

SPI CONTROLLED H-BRIDGE

DESCRIPTION The L9230 is an SPI controlled H-Bridge, designed for the control of DC and stepper motors in safety critical applications and under extreme environmental conditions. ■ OPERATING SUPPLY VOLTAGE 5V TO 28V ■ TYPICAL RDSon = 150 m? FOR EACH OUTPUT TRANSISTOR (AT 25°C) ■ CONTINOUS DC L

文件：218.23 Kbytes 頁數：25 Pages

STMICROELECTRONICS

意法半導體