5V EconoReset with Push-Pull Output

DESCRIPTION The DS1810 EconoReset uses a precision temperature reference and comparator circuit to monitor the status of the power supply (VCC). When an out-of-tolerance condition is detected, an internal power-fail signal is generated which forces reset to the active state. When VCC returns to

文件：54.68 Kbytes 頁數：5 Pages

DALLAS

Miniature Control Valve

FEATURES
1/4” or 1/2” proportional control
Interchangeable trims
CV values 0.00008 to 3.0
Air operated
Stainless Steel valve and trim standard
Linear or equal percentage control characteristics
Accurate low flow control

文件：224.37 Kbytes 頁數：4 Pages

TTELEC

5V EconoReset with Push-Pull Output

文件：122.81 Kbytes 頁數：5 Pages

MAXIM

美信

5V、經濟型復位芯片，帶有推挽輸出

DS1810 EconoReset使用精密的溫度補償基準電壓源和比較器電路監控電源(VCC)的狀態。當檢測到超出容差的情況時，會產生內部電源故障信號，強制復位為有效狀態。當VCC返回到容差范圍內的條件時，復位信號將保持有效狀態約150ms，以便電源和處理器穩定下來。 ? 發生電源故障后自動重啟微處理器\n\n? VCC返回到容差范圍內的條件后保持復位150ms\n\n? 減少對分立元件的需求\n\n? 精密溫度補償基準電壓源和電壓傳感器\n\n? 采用低成本TO-92或節省空間的表面貼裝SOT-23封裝\n\n? 推挽輸出實現低電流操作\n\n? 工作溫度：?40℃至+85℃;

ADI

亞德諾

5V EconoReset with Push-Pull Output

DESCRIPTION The DS1810 EconoReset uses a precision temperature reference and comparator circuit to monitor the status of the power supply (VCC). When an out-of-tolerance condition is detected, an internal power-fail signal is generated which forces reset to the active state. When VCC returns to

文件：54.68 Kbytes 頁數：5 Pages

DALLAS

5V EconoReset with Push-Pull Output

DESCRIPTION The DS1810 EconoReset uses a precision temperature reference and comparator circuit to monitor the status of the power supply (VCC). When an out-of-tolerance condition is detected, an internal power-fail signal is generated which forces reset to the active state. When VCC returns to

文件：54.68 Kbytes 頁數：5 Pages

DALLAS

5V EconoReset with Push-Pull Output

DESCRIPTION The DS1810 EconoReset uses a precision temperature reference and comparator circuit to monitor the status of the power supply (VCC). When an out-of-tolerance condition is detected, an internal power-fail signal is generated which forces reset to the active state. When VCC returns to

文件：54.68 Kbytes 頁數：5 Pages

DALLAS

Microprocessor Reset Circuit

Description\nThe MIC1810 is an inexpensive microprocessor supervisory circuits that monitor power supplies in microprocessor based systems.\nThe function of these devices is to assert a reset if the power supply drops below a designated reset threshold level. Several different reset threshold levels ? RESET Remains Valid with VCC as Low as 1.4V\n? Precision Voltage Monitor for 5%, 10%, or 15% drop in 5V Power Supplies\n? Available in 3-Pin SOT23 Package\n? 9μA Supply Current (typical)\n? 100ms Minimum Reset Pulse Width\n? No External Components RequiredTypical Applications\n? Portab;

Microchip

微芯科技

Package：TO-226-3，TO-92-3（TO-226AA）成形引線；包裝：卷帶（TR） 類別：集成電路（IC） 監控器 描述：IC SUPERVISOR 1 CHANNEL TO92-3

AD

亞德諾

Package：TO-226-3，TO-92-3 標準主體（!--TO-226AA）；包裝：管件 類別：集成電路（IC） 監控器 描述：IC SUPERVISOR 1 CHANNEL TO92-3

AD

亞德諾